A1972B1975C1978D1981

Correct! The Intel 8086 launched in 1978 and gave birth to the x86 architecture still used in PCs today. It was a 16-bit processor running at 5–10 MHz — a far cry from today’s multi-GHz giants. This chip laid the foundation for decades of DIY computing.

Not quite — the Intel 8086 debuted in 1978. It introduced the x86 instruction set that still underpins virtually every desktop and laptop processor sold today. IBM later used the cheaper 8088 variant for its first PC in 1981, which is sometimes confused as the origin point.

Continue

AProcessor Output Self TestBPower-On Self-TestCPrimary Operating System TransferDPower Output Signal Threshold

Correct! POST stands for Power-On Self-Test, a diagnostic routine your motherboard runs every time you boot up. It checks that critical components like RAM, CPU, and GPU are present and functional. If POST fails, you’ll often get beep codes or LED indicators to help diagnose the problem.

The correct answer is Power-On Self-Test. Every time you press the power button, your motherboard runs POST to verify that essential hardware is connected and working. Failed POST is one of the first hurdles new PC builders encounter, often caused by unseated RAM or a forgotten power connector.

Continue

ATo warm up your hands for better gripBTo check if the case is properly grounded before installingCTo discharge static electricity from your bodyDTo magnetize your fingers for handling small screws

Correct! Static electricity built up on your body can silently destroy sensitive PC components in an instant — a phenomenon called electrostatic discharge (ESD). Touching bare metal grounds you and neutralizes that charge before it can zap your CPU or RAM. Anti-static wrist straps work even better for extended build sessions.

The answer is to discharge static electricity. Your body can carry thousands of volts of static charge without you feeling a thing, but that invisible zap can permanently damage a CPU or RAM stick. It’s one of the oldest and most important safety habits in PC building — cheap insurance for expensive parts.

Continue

AReplace the CPU thermal pasteBEnsure the monitor is plugged into the GPU, not the motherboardCReflash the BIOS using a USB driveDCheck the SATA cables are firmly connected

Correct! This is arguably the most common rookie mistake in PC building — plugging the monitor into the motherboard’s video output when a dedicated GPU is installed. The motherboard’s HDMI or DisplayPort is disabled by default when a GPU is present. Always connect your display directly to the graphics card.

The most common culprit is having the monitor plugged into the motherboard’s video port instead of the dedicated GPU. When a graphics card is installed, most systems disable the motherboard’s integrated video outputs automatically. It’s such a frequent mistake that it has become a running joke in PC building communities.

Continue

AIt acts as an adhesive to hold the cooler in place permanentlyBIt fills microscopic imperfections between the CPU and cooler to improve heat transferCIt insulates the CPU from electrical interference caused by the coolerDIt lubricates the cooler’s fan bearings for quieter operation

Correct! Even finely machined metal surfaces have tiny imperfections and air gaps at the microscopic level. Thermal paste — also called thermal interface material (TIM) — fills those gaps to ensure maximum heat conduction from the CPU to the cooler. Without it, air pockets act as insulation and temperatures can skyrocket dangerously.

Thermal paste fills microscopic gaps between the CPU lid and the cooler’s base plate. Metal surfaces may look flat and smooth, but at a microscopic scale they’re riddled with tiny ridges and valleys that trap air — and air is a terrible heat conductor. A thin, even layer of thermal paste eliminates those gaps and keeps temperatures in check.

Continue

AAMD in 1990BASUS in 1993CIntel in 1995DIBM in 1988

Correct! Intel introduced the ATX (Advanced Technology Extended) standard in 1995, replacing the older AT form factor. ATX standardized component placement, power supply connectors, and airflow direction — making DIY builds far more practical and interchangeable. Nearly 30 years later, ATX and its derivatives like Micro-ATX and Mini-ITX still dominate the market.

ATX was introduced by Intel in 1995. It was a major leap forward from the previous AT standard, defining a common layout for motherboards, cases, and power supplies that made mixing and matching components from different vendors straightforward. That standardization is a huge reason DIY PC building became so accessible.

Continue

ASlots 1 and 2 (the first two slots nearest the CPU)BSlots 1 and 3, or slots 2 and 4 (alternating slots)CSlots 3 and 4 (the two slots farthest from the CPU)DAny two adjacent slots work equally well

Correct! Dual-channel mode requires RAM to be installed in matched pairs on alternating slots — typically A2 and B2, or slots 2 and 4. This allows the memory controller to access both sticks simultaneously, effectively doubling memory bandwidth. Your motherboard manual will show the exact recommended slots, usually color-coded for convenience.

To enable dual-channel mode, RAM should go in alternating slots — such as slots 2 and 4, often color-coded on the motherboard. Placing both sticks in adjacent slots (like 1 and 2) forces single-channel operation, which can noticeably reduce performance in memory-intensive tasks. Always check your motherboard manual for the exact recommended configuration.

Continue

AA rattling sound from an improperly secured case fanBA high-pitched noise produced by electromagnetic vibration in inductors under high electrical loadCThe sound of a CPU cooler fan spinning at maximum speed during stress testsDNoise caused by the hard drive’s read/write head seeking data rapidly

Correct! Coil whine is a high-pitched, sometimes whirring or buzzing noise caused by tiny electromagnetic coils (inductors) on a GPU or PSU vibrating at audible frequencies under heavy electrical load. It’s technically a defect in manufacturing tolerances but is extremely common and not usually harmful to the component. Ironically, it’s often loudest in high-end GPUs under uncapped framerates.

Coil whine is that annoying high-pitched squeal coming from inductors on your GPU or power supply vibrating under electrical load. It tends to be loudest when framerates are uncapped or during heavy computational tasks. While alarming to new builders, it’s usually harmless — though some manufacturers will replace components with severe coil whine under warranty.

See My Score